Are your Water Heater Repair services available in Lexington?

Yes, Masters Plumbing Service provides round-the-clock Water Heater Repair services directly in Lexington, GA.

How much does emergency service cost in Lexington?

We offer upfront, transparent pricing with no hidden fees for all service calls in Lexington.

🔥 Gas, Electric & Tankless Specialists

Cold Showers End Here: Water Heater Repair in Lexington, GA by Masters Plumbing Service

Name: Masters Plumbing Service
Telephone: +1-855-718-1500
Price range: $$
Rating: 4.9

A water heater failure isn't always obvious. Rust-colored hot water, a popping or rumbling noise from the tank, water pooling around the base, or a T&P valve that keeps lifting — each symptom points to a specific component failure. Our techs in Lexington know what each one means and carry the parts to address it.

📞 Call +1-855-718-1500 — Same-Day Service

Gas & Electric Certified in GA Tankless Specialists Parts Stocked On-Truck Repair or Replace — You Decide

Licensed Water Heater Repair service in Lexington, GA - Masters Plumbing Service

Our Qualifications

Why Lexington, GA Homeowners Call Masters Plumbing Service for Water Heater Work

Water heater work involves gas lines, electrical systems, and pressure vessels — it isn't a DIY project or a job for a generalist. Our techs specialize in water heater diagnosis and carry certifications specific to gas appliance work in GA.

📋

Accurate Diagnosis First

Our diagnostic process isolates the failed component so we're replacing the part that actually failed — not throwing money at the unit hoping something works.

🔩

Stocked for Same-Visit Repairs

For tankless units, we stock igniter assemblies, flow sensors, and descaling supplies for the major brands. If a specialty part isn't on the truck, we source it quickly and schedule a rapid return.

⚖️

Honest Repair vs. Replace Guidance

We give you the numbers. If repair costs approach 50–60% of a replacement unit's installed price and the tank is 8+ years old, we tell you — along with the reasons a new unit makes more financial sense. If the unit is young and the repair is minor, we say that too.

📜

Code-Compliant Installation

Every water heater installation in GA must meet current plumbing and mechanical codes — proper strapping for seismic zones, expansion tank where required by closed-loop systems, pressure-relief valve discharge piped to within 6 inches of the floor, and correct flue sizing for gas units. We pull permits where required and schedule inspections.

What We Repair & Replace

Tank, Tankless, and Heat Pump — We Service Them All

From a 40-gallon gas tank to a high-efficiency condensing tankless unit, we carry the knowledge and parts to diagnose and repair it in Lexington, GA.

Gas Tank

Gas Water Heater Repair

We test the gas supply pressure at the unit, check the thermocouple millivolt output with a meter, inspect the burner assembly for debris, and confirm proper draft on the flue. Each of these takes minutes and tells us exactly what component to replace.

Electric Tank

Electric Water Heater Repair

A failed upper element causes loss of hot water entirely. A failed lower element produces hot water but in smaller volume than expected. Knowing which symptom you're seeing before we arrive helps us confirm the likely failure quickly on-site.

Tankless

Tankless Water Heater Repair & Descaling

Tankless units fail in specific, diagnosable ways: ignition failures (error codes related to the igniter or flame rod), flow sensor malfunctions (unit won't fire when water runs), heat exchanger scale buildup (error codes for overtemp or reduced flow), and venting issues (pressure switch errors on direct-vent units). We read the error code, check the relevant component, and repair or replace what's actually failed.

Safety

T&P Valve Replacement

The temperature and pressure relief valve is a critical safety component on every water heater. It should discharge if tank temperature exceeds 210°F or pressure exceeds 150 PSI. A T&P valve that's dripping constantly, won't reset after testing, or shows visible corrosion needs immediate replacement — it's failing in the closed position, which removes the safety protection it provides.

Longevity

Anode Rod Replacement

The sacrificial anode rod — typically magnesium or aluminum — corrodes preferentially inside the tank, protecting the steel tank lining from rusting. When it's depleted, the tank wall begins corroding instead. Most anode rods last 4–6 years in normal water conditions; hard water or water softener use accelerates depletion.

Replacement

Full Water Heater Replacement

We also convert tank-to-tankless installations where the existing infrastructure supports it, including proper gas line sizing for tankless BTU demand and dedicated electrical circuit installation for electric tankless units.

📞 Call +1-855-718-1500 — Diagnose Today

Our Process

How We Handle a Water Heater Repair Call in Lexington, GA

Here's what a Masters Plumbing Service water heater service call looks like in Lexington, GA.

Describe the Symptoms When You Call

Knowing the unit's fuel type (gas or electric), tank size, and approximate age also helps us pre-load relevant parts.

Component-Level Diagnosis On-Site

This focused approach produces a clear diagnosis in 15–20 minutes rather than a vague "it's old and needs to be replaced" recommendation.

Repair vs. Replace Quote

You receive a flat-rate quote for the repair and, if relevant, a replacement option with installed price for comparison. We walk through the numbers with you — repair cost vs. unit age vs. replacement cost — and let you decide.

Same-Visit Repair or Replacement

Approved repairs happen immediately. If we're replacing the unit, we drain and disconnect the old tank, install the new unit with proper flex connectors and expansion tank where required, verify the flue or venting, and test the unit to confirm recovery temperature.

Customer Reviews

Water Heater Repair Reviews From Across Lexington, GA

★★★★★

Gas water heater stopped heating on a Thursday evening. Masters Plumbing Service had a tech out Friday morning who tested the thermocouple — millivolt output was at 12mV, well below the 25mV minimum the gas valve needs to stay open. He replaced the thermocouple and pilot assembly in about 45 minutes, total cost was well under $200. Didn't try to sell me a new heater at all — straightforward, honest diagnosis.

— B. Larson, Lexington

★★★★★

{Electric water heater wouldn't recover — we'd get about 10 minutes of hot water and then cold. Masters Plumbing Service's tech identified the lower heating element had failed. He drained the tank, replaced the element and lower thermostat while he was in there, and restored full recovery capacity. Explained the difference between upper and lower element function which I'd never understood before.|Woke up to the floor drain running under our water heater — the T&P valve was dripping continuously. The tech identified it wasn't just dripping from normal thermal expansion but was a valve that had corroded open. Replaced the valve, re-routed the discharge pipe to code, and verified tank pressure was within normal range before leaving.}

— M. Torres, Lexington, GA

★★★★★

Called about a tankless that had lost ignition — error code on the display. Tech checked the flame rod, found it had a cracked ceramic insulator causing an intermittent short. Replaced the igniter assembly, unit fired clean on the first restart. He also checked the venting for any obstructions since venting issues can cause similar ignition faults.

— J. Eriksen, Lexington, GA

Trusted Water Heater Repair service in Lexington, GA - Masters Plumbing Service

Common Questions

Water Heater Repair Questions from Lexington, GA Homeowners

A pilot that lights but won't stay on almost always indicates a failed thermocouple — it's a $15–$40 part that takes under an hour to replace. This is a repair, not a replacement scenario, unless the unit is over 12 years old and showing other signs of wear. We test the thermocouple output with a millivolt meter to confirm it's the cause before ordering the part.

Visible rust staining on the outside of the tank near the base or around the T&P valve outlet often indicates internal corrosion. Once the tank lining is breached, no repair holds long-term. An honest assessment includes checking for these signs before recommending a repair that won't last.

In some cases, rusty hot water in an older tank signals that internal corrosion is already advanced and the tank is near end of life. We inspect the anode rod condition when we diagnose this complaint and give you an honest read on whether replacement makes sense.

Popping and rumbling from a gas or electric tank water heater is almost always sediment buildup on the tank floor — a layer of mineral scale that has precipitated out of the water supply and settled. When the burner fires or the element heats, water trapped under the sediment layer steams through it, creating the popping sound.

Some Lexington, GA municipalities have expedited permit processes for water heater replacements. We know the local requirements in Lexington and handle the administrative side so you don't have to.

Common repairs — thermocouple, heating element, T&P valve — complete in 45 minutes to 1.5 hours. A full gas valve replacement takes 1.5–2 hours including testing the unit through a complete heat cycle. Tankless descaling runs 1–2 hours. Full replacement of a tank water heater takes 2–3 hours including draining, disconnecting, installing, and testing the new unit.

Cold Showers End Here: Water Heater Repair in Lexington, GA by Masters Plumbing Service